Envelope Pillow with Piping Tutorial

Video Description

blog post with more: https://www.melaniekham.com/envelope-pillow-with-piping-tutorial/ Subscribe for more Crafty Videos! http://bit.ly/MelanieHam More Simple Sewing Tutorials http://bit.ly/simplesewingtutorials Follow me on Social! Blog: http://www.melaniekham.com Facebook: https://www.facebook.com/melaniehamdesigns Twitter: https://twitter.com/#!/melanieham Pinterest: http://pinterest.com/melanieham/ Instagram: http://instagram.com/melaniekham Snapchat: MelanieKHam PLEASE READ: I serged my seam on the inside of my pillow to keep it from fraying. You may also zig zag. Also, no need to clip your corners on this project ;) Check out my blog post about it! http://www.melaniekham.com/envelope-pillow-with-piping-tutorial/ Materials Main fabric (mine is from Joann fabrics in the upholstery section - Nate Berkus binding fabric - Kona Cotton 1/2 yard 6/32 cotton cording or something similar http://amzn.to/1GUDICS pins http://amzn.to/1HBCQqi rotary blade and mat http://amzn.to/1HCG4fc sewing machine and coordinating thread http://amzn.to/1GUDKdH iron/ironing board Measurements 16 inch pillow form (1) 17 x 17 inch for front panel (2) 17 x 12 for back panels 73 inches of bias binding - Add all four sides and add 5 inches. 14 inch pillow form (1) 15 x 15 inch front panel (2) 15 x 11 65 inches of bias binding - Add all four sizes and add 5 inches 20 inch Pillow form (1) 21 x 21 inch fron panel (2) 21 x 14 for back panels 89 inches of bias binding Written Instructions: Prewash and iron fabric Cut out fabric pieces to specified size Take the back 2 pieces to the ironing board and iron the longer (horizontal) edge over 1/4 and again 1/4 inch to prepare for sewing. (:52) Sew down both seams that you just pressed with a coordinating thread about 1/8 away from the edge.(1:00) Take our fabric for your binding and make straight edges. Mine was 1/2 yard. (1:09) Take the selvedge edge of the fabric and fold it diagonally so that it lines up with the straight edge of our fabric (1:25) -the diagonal fold is the bias. It gives the binding more give and stretch to get around the corners. Fold the bias edge on top of itself 2 times keeping the folded edge lined up (1:45) Turn fabric so that your folded bias edge is on the right had side and trim the fold to create a straight edge (2:12) Flip that cut edge to the left side of the mat and using the ruler, make 3 cuts or however many you need to get appropriate bias binding size (2:20) Trim all bias strips so that it is a straight rather than diagonal edge (3:00) Join all bias binding strips with a bias join (3:14) Fold the end of the bias strip about 3/4 inch and place your cording inside (4:01) Fold the strip with the cording inside, matching up the raw edges and pin in place (4:08) Using a zipper foot or cording foot, sew a stitch as close to the cording as possible using a thread that blends with your fabric, back stitch on both ends (4:12) Attach the binding to the front square of the pillow pieces with pins very well.. (4:53) Match up the raw edges and put small cuts in the cording tape to go around the corners. (4:57) Trim end of the piping and place inside the fold from the beginning of the piping to conceal the end. (5:35) Using the zipper foot, sew the pinned piping to the front panel of the pillow back stitching at beginning and end.. Go slow around the corners.(5:53) Place front panel right side facing up and take the first back panel and lay the right side down (right sides together). The finished seam should be in the center of the pillow, raw edges should be matched up on the outside. Place 2nd back panel on top of the first, right side down with the seam toward the center and the raw edges matching on the outside edge. (6:56) Pin in place (7:10) Sewing all the pieces together with the zipper foot. Seam allowance should be between 1/2 and 5/8 inch. Remove pins as you go, and go slow around the corners. Back stitch at front and back as well as the openings. (7:21) OPTIONAL To make your pillow more washer friendly, serge or zig zag stitch your inside seam. No need to clip the corners. You are done! *This contains affiliate links, THANK YOU for the support in this way! I receive a small % if you purchase the items I have linked, plus it makes it easy for you to find ;).